Memory timings or RAM timings describe the timing info of a memory module or [[http://gbtk.com/bbs/board.php?bo_table=main4_4&wr_id=152862|neural entrainment audio]] the onboard LPDDRx. Due to the inherent qualities of VLSI and microelectronics, memory chips require time to fully execute commands. Executing commands too rapidly will result in knowledge corruption and leads to system instability. With acceptable time between commands, memory modules/chips could be given the opportunity to completely change transistors, cost capacitors and correctly sign again data to the memory controller. Because system efficiency depends upon how briskly memory can be used, this timing directly impacts the efficiency of the system. The timing of trendy synchronous dynamic random-access memory (SDRAM) is usually indicated utilizing four parameters: CL, TRCD, TRP, Memory Wave and TRAS in units of clock cycles; they're generally written as 4 numbers separated with hyphens, e.g. 7-8-8-24. The fourth (tRAS) is commonly omitted, or a fifth, the Command price, typically added (usually 2T or 1T, additionally written 2N, 1N or CR2). [[https://www.youtube.com/embed/2F_HJraoZxs?rel=0&modestbranding=1&showinfo=0&iv_load_policy=3|external site]] These parameters (as half of a larger complete) specify the clock latency of certain particular commands issued to a random access memory. Decrease numbers indicate a shorter wait between commands (as decided in clock cycles). RAS : Row Deal with Strobe, a terminology holdover from asynchronous DRAM. CAS : Column Address Strobe, a terminology holdover from asynchronous DRAM. TWR : Write Restoration Time, the time that must elapse between the last write command to a row and precharging it. TRC : Row Cycle Time. What determines absolute latency (and thus system performance) is determined by both the timings and the memory clock frequency. When translating memory timings into precise latency, timings are in units of clock cycles, which for double data [[https://www.biggerpockets.com/search?utf8=%E2%9C%93&term=charge%20memory|charge memory]] is half the speed of the generally quoted transfer rate. Without knowing the clock frequency it's inconceivable to state if one set of timings is "faster" than another. For instance, DDR3-2000 memory has a a thousand MHz clock frequency, which yields a 1 ns clock cycle. With this 1 ns clock, a CAS latency of 7 provides an absolute CAS latency of 7 ns. Faster DDR3-2666 memory (with a 1333 MHz clock, or 0.Seventy five ns precisely; the 1333 is rounded) may have a bigger CAS latency of 9, however at a clock frequency of 1333 MHz the period of time to wait 9 clock cycles is barely 6.75 ns. It is for this reason that DDR3-2666 CL9 has a smaller absolute CAS latency than DDR3-2000 CL7 memory. Each for Memory Wave DDR3 and DDR4, the four timings described earlier usually are not the one related timings and give a really quick overview of the performance of memory. The total memory timings of a memory module are stored inside of a module's SPD chip. On DDR3 and DDR4 DIMM modules, this chip is a PROM or EEPROM flash memory chip and accommodates the JEDEC-standardized timing table data format. See the SPD article for the desk format amongst different versions of DDR and examples of different memory timing info that's present on these chips. Fashionable DIMMs include a Serial Presence Detect (SPD) ROM chip that accommodates recommended memory timings for automated configuration in addition to XMP/EXPO profiles of sooner timing information (and higher voltages) to allow for a efficiency increase by way of overclocking. The BIOS on a Computer might allow the person to manually make timing changes in an effort to extend efficiency (with possible risk of decreased stability) or, in some cases, to extend stability (by using advised timings). On Alder Lake CPUs and later, tRCD and tRP are now not linked, while earlier than Intel did not allow to set them to completely different values. DDR4 introduced help for FGR (nice granular refresh), with its own tRFC2 and tRFC4 timings, whereas DDR5 retained solely tRFC2. Note: Memory bandwidth measures the throughput of memory, and is mostly limited by the transfer price, not latency. By interleaving access to SDRAM's a number of inner banks, it is possible to switch information constantly at the peak switch charge. It is possible for elevated bandwidth to come back at a value in latency. Particularly, every successive generation of DDR memory has greater transfer rates however absolutely the latency does not change significantly, and especially when first appearing on the market, the brand new technology generally has longer latency than the earlier one. The architecture and bugs in the CPUs may change the latency. Increasing memory bandwidth, even whereas rising memory latency, might improve the efficiency of a pc system with multiple processors and/or a number of execution threads. Greater bandwidth can even enhance efficiency of built-in graphics processors that have no dedicated video memory but use common RAM as VRAM. Modern x86 processors are closely optimized with techniques such as superscalar instruction pipelines, out-of-order execution, memory prefetching, memory dependence prediction, and branch prediction to preemptively load memory from RAM (and other caches) to hurry up execution even additional. With this quantity of complexity from efficiency optimization, it's troublesome to state with certainty the consequences memory timings may have on performance. Completely different workloads have completely different memory access patterns and are affected otherwise in efficiency by these memory timings. In Intel programs, memory timings and management are dealt with by the Memory Reference Code (MRC), a part of the BIOS. A lot of it is also managed in Intel MEI, Minix OS that runs on a devoted core in PCH. Some of its subfirmwares can have impact on memory latency. Stuecheli, Jeffrey (June 2013). "Understanding and Mitigating Refresh Overheads in High-Density DDR4 DRAM Techniques" (PDF). 2007-11-27). "The life and times of the trendy motherboard". Pelner, Jenny; Pelner, James.